How To Make 3D Resin Flowers: A Step-By-Step Guide To Resin Blooms (2024)

ArtistElena Gribanova from Allure Decorationhas mastered the technique of 3D resin flowers and is here to explain how it's done. Follow Elena's step-by-step techniques andtutorial to learn the basics and then change up the color palette and petal shape to create your very own custom look!

Let's get started with our tutorial on making 3D resin flowers.

Warm the resin and hardener bottles (with the lids on) in a warm water bathprior to measuring and mixing. The water should be as warm as it would be for a baby's bath, i.e., not hot or boiling. Warming the resin will thin it out and help to reduce the amount of bubbles when you pour into the molds.

Allow the resin to sit in the warm water bath for approximately 10-15 minutes. When the resin is warmer than room temperature, you'll know it's ready.

💡TIPS: Ensure that no water comes in contact with the resin: keep the lids on, do not submerge the bottles and dry them off thoroughly before opening them.

Mix the resin and hardener together slowly,

Once the resin has been mixed, allow it to sit for approximately 15 minutes.This will allow the bubbles time to rise to the surface and will also encourage the resin to thicken up a little bit to prevent the ink from spreading.

Portion out the resin into individual cups, one per color.Separate approximately 30-40 ml of resin for light blue in one cup, and 10-15 ml for white in another.

Add 1-2 drops of blue alcohol ink into the first cup and test the color. Remember, it's always best to add less to start with. You can add more if necessary,but you can't take it away.

Add a squeeze of white into the second cup. You want the white to be a little thicker than the blue.

Pour the clear resin into the mold, starting in the center and allowing the resin to spread out over the entire surface. Pour until the mold is just a little over halfway full.

💡 TIP: Don't hold the heat gun too closeor in one spot for too longor you risk damaging the mold and overheating the resin.

Add more resin to the mold until it's almost full.Use the heatgun once again to get rid of surface bubbles.

Now we're ready to decorate the flowers!

Run the heat gun over the mold once againto eliminate any bubbles.

Use the heatgun to eliminate any bubbles.

Drop purple alcohol ink dots all the way around the glitter center.

Add a row of blue alcohol ink drops in between the purple dots.

Add a few more drops (approximately 4 drops) of purple in the center. Once you've added the purple drops, allowthe ink to sit for a little while while you prepare the white resin.

Pour the white resin intoa piping bag or a ziploc bag set in a plastic cup.

Push the resin down to the bottom of the bag, ensuring there are no air pockets in the resin, then secure the bag with a knot and/or a plastic clip.

Snip a tiny opening in the bottom of the bagwith a sharp pair of scissors.

Use the heatgun over the molds once more to get rid of any bubbles that may have risen to the surface.

💡TIP: If you find you have a lot of fine microbubbles, you can sprinkle a little fine glitter over the surface of the resin. This will mimic the bubbles and create a sparkly effect.

Starting in the center of the flower, create 5-6 rows of petal shapes using the piping bag. The shape of the petal and design of the flower is completely up to you.
💡TIP: If you need some inspiration, use a photo of your favorite flower or a real life flower as reference!

💡TIP: You'll notice the white resin will start to sink. Touch up as needed, if you missed a spot or notice the white has sunk too much.

Use the heat gun once more and then allow the resin to sit for a few minutes.

Dip a toothpick into the resin at the center of the mold to get a little purple resin on the tip. Insert the toothpick at the edge of the mold and drag it towards the center. Repeat this step at even intervals until you have 12 evenly spaced lines all the way around the center.

If you see empty spaces, touch up the petals with a little more white resin from the piping bag.

Use the heat gun one more time to eliminate surface bubbles.

Cover with a dustcover and leave it until the next day.

When you first remove the coasters from the mold, you'll notice that the resin is bendy. This is because it hasn't finished curing yet. It needs to sit somewhere perfectly flat, for up to a week, to cure completely.

💡TIP: If you want to transform the coaster into a trinket dish, find a shallow plastic bowl to lay the bendy resin into. Allow it to cure and after a few days, it will take on the shape of the bowl.

Once your coasters have cured, they are ready to use, to gift or to sell as part of your own resin business! Each one is a unique work of art: you can leave them as they are or you can use a gold leaf paint marker to finish off the edges for a little extra sparkle.

Read if you can use artresin to make coasters and hot plates!

We hope you've enjoyed learning how to create stunning 3D Flower Coasters. Please leave any questions in the comments below and our customer service team will be happy to get back to you!